Release notes for UBEX MMU
v1.1.0b10
New feature:
-
Centralized System Update is available - The Firmware update of the Endpoints are managed by the MMU.
-
Grid Video Wall is implemented.
-
Adding support of Rental Endpoints.
-
Command injection to IR endpoint ports is available.
Bugfix:
-
Adding missing 4K EDIDs (F146 - F148) to the Factory EDID list.
-
Fixing RemoteIP problem by implementing periodic membership report to multicast groups.
-
Fixing crash caused by TcpTunnel in debug mode.
Known issue:
-
In video wall setups, upscaling is not fully supported. (e.g.: 4K video content displayed on a 2-by-2 video wall where the resolution of the displays is 4K).
-
In tile view handling of video walls is limited, it is recommended to use the grid view for video walls.
Endpoint (v1.3.1b5)
New feature:
-
Source locked mode is now supported.
-
Scaling and frame rate conversion are also supported on transmitter side.
-
The frame rate converter and scaler modules support image cropping in case of downscaling in center image position.
-
12-bit deep color HDMI signals can be transmitted in 10 bit mode.
-
Added support for Transceiver mode
-
Added support for scaling to the default resolution of the attached display (EDID-based scaling)
-
Added support for F110 variant (analog audio in/out, RS-232)
-
Added support for upgrading endpoints in matrix mode with LDU2
-
Added support for No Sync Screen generation on TX/TRX sources (for network diagnostics)
-
Added support for LDC Orientation Preference setting
-
Improved LLDP support (reporting operation mode and package version)
-
Added identify() method to S and O nodes
-
Fixed channel status data for analog audio inputs
-
Refined fan control (silent operation)
-
Added support for R100 part numbers
-
Added support for IR in F110
-
Added support for centralized firmware update
Bugfix:
-
4K60 4:4:4 and 4K30 4:4:4 signals can be passed through at the same time.
-
SCDC registers are only modified, if the connected display supports this protocol.
-
More robust SCDC handling is introduced.
-
Fixed issue with detecting HDMI 1.x sources after receiving 4K@60 Hz
-
Fixed 4K@30 Hz transmission over a single 10G link
-
Fixed image artifacts with a few scaling configurations
-
Signal properties are reported on unconnected outputs as well
-
All RX/TX mode related settings are cleared when operation mode is changed
-
Fixed issues with fan control
-
Added support for LW3 configuration backup and restore
-
Fixed issue with color space conversion for DVI inputs
-
Fixed a glitch with updating dynamic EDID's
-
Improved stability of the embedded bootloader
-
Fixed a glitch with some 10G switches not switching streams atomically
Known issue:
-
4k60 4:4:4 and 4k30 4:4:4 signals can not be passed through at the same time with this version.
-
12-bit deep color HDMI signals can not be transmitted with this version, black image is generated in this case.
-
The configuration restore procedure works on the same type of operation modes only
-
HBR audio formats (Dolby TrueHD; DTS-HD Master Audio 7.1) are not supported
-
4:2:0 sampling is supported on the output ports of the receiver in pass-through mode only
-
The frame rate converter and the scaler do not support image cropping in case of downscaling in center image positon mode. The image will be substituted with white screen.
-
Video output is unstable when scaling a precropped image to 4K@60
v1.0.7b1
Bugfix:
-
Terminal messages are shown on the local serial port of the MMU during boot time.
-
In LDC, on the tile of the endpoint RS-232 ports, the command injection port is not updated after changing it on the property panel.
-
In LDC, on the port property panel, the databits field of the endpoint RS-232 ports is empty, the databit count is always 8 bits.
v1.0.6b12
New feature:
-
Command injection to RS-232 endpoint ports is available
-
NTP client is available
-
Supports UBEX-PRO20G-HDMI-F110 endpoints (Analog audio input and output, RS-232)
-
Redesigned device properties
-
Supports configuration and tagging of RS-232 and Ethernet endpoint ports
-
Supports TRX2 mode for UBEX-PRO20G-HDMI-F100 and UBEX-PRO20G-HDMI-F110 endpoints
-
Video and Audio cross-point Tile View
Bugfix:
-
General improvements on stabiliy
-
Fixing firmware update issues.
Known issue:
-
In LDC, on video cross-point tile view, the not available connection of the TRX2 mode (local video loop-back) is not displayed properly.
-
In LDC, on the port property panel, the databits field of the endpoint RS-232 ports is empty, the databit count is always 8 bits.
-
In LDC, on the tile of the endpoint RS-232 ports, the command injection port is not updated after changing it on the property panel.
-
Command injection to IR endpoint ports is not available.
v1.0.4b1
Bugfix:
-
Fixed configuration loss during backup-restore and firmware upgrade. This issue was only present in package version 1.0.3b1.
Please be sure to store a backup of your configuration before upgrading from v1.0.3b1 to v1.0.4b1. Upgrades from other versions are not affected.
v1.0.3b1
Bugfix:
-
Fixed a bug that caused the MMU not being able to reload the configurations for the endpoints with 918200## part number after the reset of the MMU.
v1.0.2b1
Bugfix:
-
LCD re-initialisation issue is fixed.
v1.0.1b5
New feature:
-
The MMU built-in web control software is available.
-
System log viewer is available in the built-in web control software.
-
Basic LCD menu is available to set Network settings and reset the Ubex MMU to factory defaults.
Known issue:
-
Only basic bandwidth management is supported. (HDMI1 channel has high priority, if bandwidth limit is exceeded by HDMI1 and HDMI2 streams, HDMI2 is not transmitted or received.)
-
MMU managed Endpoint firmware update is not supported, the Endpoints have to be updated separately by the LDU2 software.
-
Only one MMU per network is supported.
-
Control USB is not supported, it is recommended to control the MMU through the Control Ethernet Interface.
-
LW2 simple protocol is not supported, it is recommended to use LW3 protocol to control the MMU.
-
Video and Audio cross-point mute and lock functions are not available.
v1.0.0b6
Known issue:
-
Only basic bandwidth management is supported. (HDMI1 channel has high priority, if bandwidth limit is exceeded by HDMI1 and HDMI2 streams, HDMI2 is not transmitted or received.)
-
The LCD menu is not supported.
-
LW2 simple protocol is not supported, it is recommended to use LW3 protocol to control the MMU.
-
Video and Audio cross-point mute and lock functions are not available.
-
The MMU built-in web control software is in beta state, using LDC is recommended.
-
Control USB is not supported, it is recommended to control the MMU through the Control Ethernet Interface.
-
Only one MMU per network is supported.
-
MMU managed Endpoint firmware update is not supported, the Endpoints have to be updated separately by the LDU2 software.